fbpx

Projects

  • All
  • Hydraulic
  • Electromechanical
  • Engineering
  • Scanning

Support structure design

Conception d'une structure de support capable de soutenir 55 tonnes pour le remplacement de l'entraînement d'un épaississeur. Cette réussite a été possible grâce à une collaboration étroite entre toutes les parties prenantes. Mine Canadian Malartic et groupe Altan (Tristan Rivest-Abel).

Custom data acquisition and display module

Custom-built module that acquires the signal from 8 pressure sensors and displays the reading. Enables diagnosis of the machine's hydraulic system at specific points.

Crusher structure

Design of a structure for a cone crusher, calculations and drawings for manufacturing.

Clamping table

Complete refurbishment of hydraulic system, hoses and fittings with our Forsaflex and Rexroth product ranges.

Pump assembly

Montage de cinq pompes hydrauliques Bosch Rexroth, incluant une pompe A4VSO500, deux pompes A10VO45 et une pompe à "gear" triple.

Hydraulic assembly of a drilling console

Turnkey project. Complete assembly of the hose and fitting system for a diamond drill operating console. The hoses and fittings are from the Forsaflex range.

3D scanning of a dumpbox

Scanning of a Prinoth T8 tracked vehicle's. The objective was to scanning the truck, particularly the dumpbox, in order to make modifications to the equipment. The 3D drawing was obtained. Afterwards, it is possible to draw plans from the 3D.

Lubrication system for an excavator bucket

Complete refurbishment of the lubrication system for the bucket of an excavator found in the mining field. The project consisted of installing new hoses and hydraulic adapters.

Hydraulic power pack

Design of a turnkey hydraulic power pack for a customer. Manufactured with Bosch Rexroth components (AA10VSO pump and M4 body valve).

Development of a data acquisition system

Development of a data acquisition system for hydraulic pressure sensors as well as a web interface that allows real-time display of data.

Modernization of the hydraulic system of a paving machine

Complete modernization of the hydraulic system of a paving machine. Installation of the hydraulic system including the hoses and the pump, as well as the addition of a gas engine.

Hydraulic lubrication unit

Design of a hydraulic lubrication unit according to the customer's specifications.

Manufacture of electronic controller

Custom manufacturing of an electronic speed controller for equipment.

Manufacture of controller for test bench

Custom-made controller to control different electrical signals during the tests with the test bench.

Creation of controller for hydraulic cylinder

Our specialists have manufactured a controller allowing the verification of linear sensors of hydraulic cylinders. Discover the project here.

Custom trailer design

Custom trailer design for the transport of Cubex drills, created by Forcetech in collaboration with the customer, Machine Roger International.

3D scanning of the components of a Cubex

3D scanning of all Cubex MRI components in order to make a parts book, as well as the manufacturing drawings.

Bumper R1700G

Using 3D scanning technology, it was possible to scan the existing R1700G bumper (yellow) and make modifications (red) to strengthen it. Agnico Eagle Mine - Goldex Division.

Power Pack

HP Hydraulique challenged itself to manufacture a Power Pack according to the requirements of its customer, Canadian Malartic Mine.

Hydraulic system

HP Hydraulique had the mandate to install a hydraulic and lubrication system on a mobile equipment for its customer.

Repair of a Bosch Rexroth 1000cc pump

HP Hydraulique repaired and refurbished a Bosch Rexroth 1000cc pump for its customer.

Coating on excavator buckets

In order to obtain a larger opening of the buckets, the 3D digitizing of the buckets and the wear coatings were carried out. It was then possible to optimize the wear linings in conjunction with the client, Canadian Malartic Mine.

Clamping table

Complete refurbishment of hydraulic system, hoses and fittings with our Forsaflex and Rexroth product ranges.

Pump assembly

Montage de cinq pompes hydrauliques Bosch Rexroth, incluant une pompe A4VSO500, deux pompes A10VO45 et une pompe à "gear" triple.

Hydraulic assembly of a drilling console

Turnkey project. Complete assembly of the hose and fitting system for a diamond drill operating console. The hoses and fittings are from the Forsaflex range.

Lubrication system for an excavator bucket

Complete refurbishment of the lubrication system for the bucket of an excavator found in the mining field. The project consisted of installing new hoses and hydraulic adapters.

Hydraulic power pack

Design of a turnkey hydraulic power pack for a customer. Manufactured with Bosch Rexroth components (AA10VSO pump and M4 body valve).

Modernization of the hydraulic system of a paving machine

Complete modernization of the hydraulic system of a paving machine. Installation of the hydraulic system including the hoses and the pump, as well as the addition of a gas engine.

Hydraulic lubrication unit

Design of a hydraulic lubrication unit according to the customer's specifications.

Hydraulic system

HP Hydraulique had the mandate to install a hydraulic and lubrication system on a mobile equipment for its customer.

Repair of a Bosch Rexroth 1000cc pump

HP Hydraulique repaired and refurbished a Bosch Rexroth 1000cc pump for its customer.

Support structure design

Conception d'une structure de support capable de soutenir 55 tonnes pour le remplacement de l'entraînement d'un épaississeur. Cette réussite a été possible grâce à une collaboration étroite entre toutes les parties prenantes. Mine Canadian Malartic et groupe Altan (Tristan Rivest-Abel).

Crusher structure

Design of a structure for a cone crusher, calculations and drawings for manufacturing.

Custom trailer design

Custom trailer design for the transport of Cubex drills, created by Forcetech in collaboration with the customer, Machine Roger International.

Bumper R1700G

Using 3D scanning technology, it was possible to scan the existing R1700G bumper (yellow) and make modifications (red) to strengthen it. Agnico Eagle Mine - Goldex Division.

Crusher structure

Design of a structure for a cone crusher, calculations and drawings for manufacturing.

3D scanning of a dumpbox

Scanning of a Prinoth T8 tracked vehicle's. The objective was to scanning the truck, particularly the dumpbox, in order to make modifications to the equipment. The 3D drawing was obtained. Afterwards, it is possible to draw plans from the 3D.

3D scanning of the components of a Cubex

3D scanning of all Cubex MRI components in order to make a parts book, as well as the manufacturing drawings.

Coating on excavator buckets

In order to obtain a larger opening of the buckets, the 3D digitizing of the buckets and the wear coatings were carried out. It was then possible to optimize the wear linings in conjunction with the client, Canadian Malartic Mine.

Custom data acquisition and display module

Custom-built module that acquires the signal from 8 pressure sensors and displays the reading. Enables diagnosis of the machine's hydraulic system at specific points.

Development of a data acquisition system

Development of a data acquisition system for hydraulic pressure sensors as well as a web interface that allows real-time display of data.

Manufacture of electronic controller

Custom manufacturing of an electronic speed controller for equipment.

Manufacture of controller for test bench

Custom-made controller to control different electrical signals during the tests with the test bench.

Creation of controller for hydraulic cylinder

Our specialists have manufactured a controller allowing the verification of linear sensors of hydraulic cylinders. Discover the project here.

Power Pack

HP Hydraulique challenged itself to manufacture a Power Pack according to the requirements of its customer, Canadian Malartic Mine.